Keywords
Serat
Pelepah
Tungkai daun
Sagu
Abstract
Tujuan penelitian ini untuk menganalisis pengaruh ukuran besar diameter serat pelepah sagu terhadap sifat mekanik kekuatan tarik, menganalisis sifat mekanik tarik material komposit yang diperkuat serat pelepah sagu.Berdasarkan hasil penelitian; (1). Larutan NAoH berpengaruh terhadap kuat Tarik specimen, hal ini ditunjukkan pada 2,5% (NAoH terhadap H2O). Nilai kekuatan tariknya 49,486 N/mm2. (2). Serat pelepah sagu kuat tariknya jauh dibawah serat gelas. (48,435 N/mm2< 323 N/mm2). Hal ini disebabkan rongga yang terdapat di serat sintesis lebih rapat dibanding serat alami. (3). Berdasarkan variabel yang diteliti, kekuatan tarik (Ftu) dengan nilai tertinggi terjadi pada komposit (volume 85% matriks : 15% serat) yaitu sebesar 3,12 beban 11824 N. (4). Kekuatan tarik mengalami kenaikan terhadap peningkatan komposisi volume serat. (5). Spesimen uji yang mengalami regangan dan patah pada titik load yaitu pada komposisi volume 85% matriks : 15% serat sebesar 3,12 MPa dengan regangan sebesar 8% dan modulus young yang terjadi sebesar 38,615  MPa.
The purpose of this study was to analyze the effect of the size of the sago frond fiber diameter on the mechanical properties of the tensile strength, to analyze the tensile mechanical properties of the composite material reinforced by sago frond fibers. Based on research results; (1) NaOH solution affects the tensile strength of the specimen. This is shown at 2.5% (NaOH to H2O), the tensile strength value is 49.486 N/mm2. (2) Sago frond fiber has a tensile strength far below the glass fiber (48,435 N/mm2 <323 N/mm2). This is because the cavities in synthetic fibers are denser than natural fibers. (3) Based on the variables studied, the tensile strength (Ftu) with the highest value occurs in the composite (85% matrix volume: 15% fiber), which is 3.12 load 11824 N. (4) Tensile strength increases with the increase in fiber volume composition. (5) The test specimens that experienced a strain and fracture at the load point, namely the composition of volume 85% matrix: 15% fiber was 3.12 MPa with a strain of 8% and the modulus young that occurred was 38.615 MPa.
References
Ahyuni, D. (2011). Pengelolalan Sagu (Metroxylon spp) di PT National Sago Prima, selat panjang, Kab. Kepulauan Meranti, Riau, dengan Aspek Khusus Pertumbuhan Bibit di Lapangan. Skripsi. Program Sarjana. Institut Pertanian Bogor. Bogor.
Awual, M. R., Hasan, M. M., Iqbal, J., Islam, M. A., Islam, A., Khandaker, S., ... & Rahman, M. M. (2020). Ligand based sustainable composite material for sensitive nickel (II) capturing in aqueous media. Journal of Environmental Chemical Engineering, 8(1), 103591.
Awual, M. R. (2019). Innovative composite material for efficient and highly selective Pb (II) ion capturing from wastewater. Journal of Molecular Liquids, 284, 502-510
Badaron, S. F., Gecong, A., Anies, M. K., Achmad, W. M., & Setiani, E. P. (2019). Studi Perbandingan Kuat Tarik Tidak Langsung terhadap Campuran Aspal Beton dengan menggunakan Limbah Marmer dan Abu Sekam Padi sebagai Filler. PENA TEKNIK: Jurnal Ilmiah Ilmu-Ilmu Teknik, 4(2), 145-155.
Chandramohan, D., & Kumar, A. J. P. (2017). Experimental data on the properties of natural fiber particle reinforced polymer composite material. Data in brief, 13, 460-468.
Chung Deborah D. L. (2010). Composite Materials Science and Applications. Second Edition. Springer-Verlag: London
Gunawan, Y., & Aksar, P. (2016). Analisa Pengaruh Ukuran Diameter Serat Tangkai Sagu terhadap Sifat Mekanik pada Material Komposit. Enthalpy, 1(2).
Humeiri, Arif. (2013). Pengaruh konsentrasi alkali dan diameter serat terhadap kuat geser rekatan pada antar muka serat ijuk aren (arenga pinnata)/ poliester. Yogyakarta
Lestari, M.S., S.R. Sihombing, Y.H. Rusmawir, dan R. Kelyanin. (2010). Implementasi Teknologi Pengolahan Sagu Rakyat di Kabupaten Jayapura. http://papua.litbang.deptan.go.id. [9 Agustus 2019]
Ramalan. Laode, (2015). Analisis Kekuatan Tarik Dan Bending Komposit Diperkuat Serat Ijuk. (Skripsi). Universitas Halu Oleo : Kendari
Sofian Bondan. T. (2010). Pengantar material teknik. Salemba Teknika. Jakarta.
Supu, I., Tenriawaru, E. P., & Cambaba, S. (2017). Sifat Mekanik Kulit Batang Sagu Pada Berbagai Kondisi. The Indonesian Green Technology Journal, 6(1).
Wibisono, M. A. (2011). Pengelolaan Sagu (Metroxylon spp) di PT. National Sagu Prima, Kabupaten Kepulauan Meranti, Riau dengan Studi Kasus Pengaruh Teknik Persemaian dan Jenis Tanaman Induk Terhadap Pertumbuhan Bibit Sagu. (Skripsi) Program Sarjana.. Institut Pertanian Bogor. Bogor.
Yudha Yoga Pratama dkk. (2014), Pengaruh perlakuan alkali, fraksi volume serat, dan panjang serat terhadap kekuatan tarik komposit serat sabut kelapa – polyester. Jurnal Ilmiah Teknik Industri. Universitas Muhammadiyah Surakarta. Surakarta
Authors who publish in PENA TEKNIK: Jurnal Ilmiah Ilmu-ilmu Teknik agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.